The S1 button on the CC2531 is valuable for testing this. If you see the LED flash/blink RED once every 4 seconds, then it is in normal operation mode.Įnsure the CC2531 has an active link to the zigbee coordinator. Search for “lumi_router”:Įnsure the CC2531 is in “normal operation” mode. The CC2531’s red LED will slow-blink when it is joined to the network.Īfter pairing, ensure Home Assistant (HA, aka hass) has entity IDs for the CC2531 router. To pair, enable “permit” mode on your coordinator, then power-on the CC2531 and it will join the network automatically. This assumes you have already paired the CC2531 router with your zigbee coordinator (aka hub, aka gateway). ![]() The CC2531 with router firmware is a totally standalone zigbee router. This assumes you are running the CC2531 router firmware (router-cc2531-std.hex) that is part of the zigbee2mqtt project. You can simply plug the CC2531 into a USB-A charger like a smartphone charger. When using the CC2531 as a router, you do NOT need to connect it to a Raspberry Pi (or other computer). The CC2531 router works well with Xiaomi sensors, which are notoriously picky about what zigbee routers/repeaters/hubs they work with. If you are having trouble with the CC2531 as a zigbee router (aka repeater), follow these steps. Operations are the same, but CC2530 does not have LEDs. In order to re-enter normal operational model, simply remove and replace power to the device.UPDATE 5: I have upgraded to a CC2530+CC2591 router ($15 on eBay) with external antenna because I found the CC2531’s range to be too short/limiting. Reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. Press the Action Menu button and select DFU. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Press the Action Menu button and select Lock. Submit a valid PIN to reset the settings for your beacon to factory defaults. Reset the device to the original factory settings. Press the Action Menu button and select Reset. Submit a new and existing PIN to update the PIN for your beacon. Press the Action Menu button and select Update PIN. ![]() Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Press the Action Menu button and select Range. Update the measured power value with the results of your calibration activity and update your settings. Press the Action Menu button and select Calibrate.Ĭalibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Submit a valid PIN to update the settings for this beacon. Press the Action Menu button and select Apply. Select any RadBeacon in the table to view it's detailed settings. ![]() Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by swiping down on the RadBeacons table. Once discovered, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby configurable Radius Networks beacons. The RadBeacon app from Radius Networks requires an iOS iPhone, iPad or iPod touch running iOS 7.1 or higher and equipped with Bluetooth 4.0 capabilities. The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services as well as other emerging proximity services.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |